Light ball, ~ 865 m/s (2,838 ft/s) rifle ~ 800 m/s (2,625 ft/s) carbine.
Effective firing range
500 m (550 yards), 800+ m (875+ yards with optics)
5-round non-detachable magazine, loaded individually or with 5-round stripper clips.
Rear: ladder, graduated from 100 m to 2,000 m (M91/30) and from 100 m to 1,000 m (M38 and M44); Front: hooded fixed post (drift adjustable) PU 3.5 and PEM scope also mounted
The 3-line rifle M1891 (Russian: ? 1891 ?, tryokhlineynaya vintovka obraztsa 1891 goda), colloquially known in the West as Mosin-Nagant and in Russia as Mosin's rifle (Russian: , ISO 9: vintovka Mosina), is a five-shot, bolt-action, internal magazine-fed, military rifle developed from 1882 to 1891, and used by the armed forces of the Russian Empire, the Soviet Union and various other nations. It is one of the most mass-produced military bolt-action rifles in history with over 37 million units having been made since its inception in 1891, and, in spite of its age, it has been used in various conflicts around the world up to the present day. It is primarily found chambered for its original 7.62×54mmRcartridge.
Various weapons were acquired and tested by GAU of the Ministry of Defense of Russian Empire, and in 1889 the Lebel M1886 was obtained through semi-official channels from France. It was supplied together with a model of the cartridge and bullet but without the primer and the smokeless powder. Those problems were solved by Russian scientists and engineers (the smokeless powder, for instance, was produced by Dmitri Mendeleev himself).
In 1889, three rifles were submitted for evaluation: Captain Sergei Ivanovich Mosin of the imperial army submitted his "3-line" caliber (.30 cal, 7.62 mm) rifle; Belgian designer Léon Nagant submitted a "3.5-line" (.35 caliber, 9 mm) design; and a Captain Zinoviev submitted another "3-line" design (1 "line" = in or 2.54 mm, thus 3 lines= 7.62 mm).
When trials concluded in 1891, the evaluators were split in their assessment. The main disadvantages of Mosin's rifle were a more complicated mechanism and a long and tiresome procedure of disassembling (which required special instruments -- it was necessary to unscrew two fasteners). Nagant's rifle was mainly criticized for its lower quality of manufacture and materials, due to "artisan pre-production" of his 300 rifles. The commission initially voted 14 to 10 to approve Mosin's rifle. At this point the decision was made to rename the existing commission and call it Commission for creation of the small-bore rifle ( ? ), and to put on paper the final requirements for such a rifle. The inventors obliged by delivering their final designs. Head of the commission, General Chagin, ordered subsequent tests held under the commission's supervision, after which the bolt-action of Mosin's design was ordered into production under the name of 3-line rifle M1891 ( ? 1891 ?).
Like the Gewehr 98, the 1891 Mosin uses two front-locking lugs to lock up the action. However, the Mosin's lugs lock in the horizontal position, whereas the Mauser locks vertically. The Mosin bolt body is multi-piece whereas the Mauser is one piece. The Mosin uses interchangeable bolt heads like the Lee-Enfield. Unlike the Mauser, which uses a "controlled feed" bolt head in which the cartridge base snaps up under the fixed extractor as the cartridge is fed from the magazine, the Mosin has a "push feed" recessed bolt head in which the spring-loaded extractor snaps over the cartridge base as the bolt is finally closed similar to the Gewehr 1888 and M91 Carcano or modern sporting rifles like the Remington 700. Like the Mauser, the Mosin uses a blade ejector mounted in the receiver. The Mosin bolt is removed by simply pulling it fully to the rear of the receiver and squeezing the trigger, while the Mauser has a bolt stop lever separate from the trigger.
Like the Mauser, the bolt lift arc on the Mosin-Nagant is 90 degrees, versus 60 degrees on the Lee-Enfield. The Mauser bolt handle is at the rear of the bolt body and locks behind the solid rear receiver ring. The Mosin bolt handle is similar to the Mannlicher: it is attached to a protrusion on the middle of the bolt body, which serves as a bolt guide, and it locks protruding out of the ejection/loading port in front of a split rear receiver ring, also serving a similar function to Mauser's "third" or "safety" lug.
The rifling of the Mosin barrel is right turning (clockwise looking down the rifle) 4-groove with a twist of 1:9.5" or 1:10". The 5-round fixed metallic magazine can either be loaded by inserting the cartridges singly, or more often in military service, by the use of 5-round stripper clips.
Refinement and production
Schematic of Model 1891 (top left)
The 3-line rifle, Model 1891, its original official designation, was adopted by the Russian military in 1891. There have been several variations from the original rifle, the most common being the M1891/30 (commonly referred to as "the 91/30" by shooters), which was a modernized design introduced in 1930. Some details were borrowed from Nagant's design. One such detail is the attachment of the magazine spring to the magazine base plate. In Mosin's original design the spring was not attached to the base plate and, according to the Commission, could be lost during cleaning. Another detail is the form of the clip that could hold five cartridges to be loaded simultaneously into the magazine.
Another detail is the form of the "interrupter", a specially designed part within the receiver, which helps prevent double feeding. The initial rifle proposed by Mosin lacked an interrupter, leading to numerous failures to feed. This detail was introduced in the rifle borrowing from Nagant's rifle. Although the form of the interrupter was slightly changed, this alteration was subsequently borrowed back by the Commission for the Model 1891 Mosin-Nagant. During the modernization of 1930, the form of the interrupter was further changed, from a single piece to a two-piece design, as the part had turned out to be one of the least reliable parts of the action. Only the clip loading cartridges and the attachment of the magazine spring to the magazine base plate in subsequent models were designed by Nagant. Considering the rifle could be easily loaded without using a clip, one cartridge after another, the magazine spring attached to the magazine base plate is the only contribution of Nagant to all rifles after 1930.
Nagant's legal dispute
Despite the failure of Nagant's rifle, he filed a patent suit, claiming he was entitled to the sum the winner was to receive. It appeared that Nagant was the first to apply for the international patent protection over the "interrupter", although he borrowed it from Mosin's design initially. Mosin could not apply for a patent since he was an officer of the Russian army, and the design of the rifle was owned by the Government and had the status of a military secret.
A scandal was about to burst out, with Nagant threatening he would not participate in trials held in Russia ever again and some officials proposing to expel Nagant from any further trials, as he borrowed the design of the "interrupter" after it was covered by the "secrecy" status given in Russia of that time to military inventions and therefore violated Russian law. Taking into consideration that Nagant was one of the few producers not engaged by competitive governments and generally eager to cooperate and share experience and technology, the Commission paid him a sum of 200,000 Russian rubles, equal to the premium that Mosin received as the winner. The rifle did not receive the name of Mosin, because of the personal decision taken by Tsar Alexander III, which was made based on the opinion of the Defence Minister Pyotr Vannovskiy: there are parts in this newly created design, invented by Colonel Rogovtzev, by Lt.-General Chagin's Commission, Captain Mosin and small-arms manufacturer Nagant, therefore it is only fair to call it Russian 3-line rifle M1891.
The Tsar himself dashed the word "Russian" from this document with his own hand. This turned out to be a wise decision, as Leon Nagant remained the major contractor for the Russian Government, and in 1895, Nagant's revolver was adopted by the Russian army as the main sidearm.
However, for the same reason and because of Nagant's attempts to use the situation for publicity, the "Mosin-Nagant" name appeared in the Western literature (the rifle was never called this in Russia). The name is a misnomer from the legal point of view (taking into consideration the legal provisions of Russian law at that time, i.e. the law of the country to adopt the rifle) and from technical point of view, as none of the details borrowed from Nagant's design, even if removed, would prevent the rifle from firing. Moreover, from the technical point of view the rifle that came to be called "Mosin-Nagant" (or "Nagant-Mosin") is the design proposed by Mosin, as further amended by Mosin with some details being borrowed from Nagant's design. Only since 1924 the rifle was officially named the "Mosin's rifle" in the USSR, although peculiar models were still designated by a year only.
In 1889 Tsar Alexander III ordered the Russian army to meet or exceed European standards in rifle developments with "rifles of reduced caliber and cartridges with smokeless powder." The new weapons would entail high velocities, exceeding 600 meters per second (2,000 ft/s) and would result in land battles both commencing and being capable of being fought at longer ranges, nearly two kilometers. The new Mosin rifles would replace the Berdan rifles then in use by the Russian army.
The Russo-Japanese War (1904-1905) was the Mosin-Nagant M-1891[nb 1] rifle's first major "blooding", and by the time the war broke out in 1904, approximately 3,800,000 Mosin-Nagant M1891 rifles had been built, with over a million and a half in the hands of the Russian cavalry and all of his reserves when hostilities commenced.
Between the adoption of the final design in 1891 and the year 1910, several variants and modifications to the existing rifles were made.
World War I
Russian Imperial infantry of World War I armed with Mosin-Nagant rifles
With the start of World War I, production was restricted to the M1891 dragoon and infantry models for the sake of simplicity. Due to the desperate shortage of arms and the shortcomings of a still-developing domestic industry, the Russian government ordered 1.5 million M1891 infantry rifles from Remington Arms and another 1.8 million from New England Westinghouse Company in the United States in 1915. Remington produced 750,000 rifles before production was halted by the 1917 October Revolution. Deliveries to Russia had amounted to 469,951 rifles when the Treaty of Brest-Litovsk ended hostilities between the Central Powers and Russia. Henceforth, the new Bolshevik regime of Vladimir Lenin cancelled payments to the American companies manufacturing the Mosin-Nagant (Russia had not paid for the order at any time throughout the Great War).
With Remington and Westinghouse on the precipice of bankruptcy from the Communists' decision, the remaining 280,000 rifles were purchased by the United States Army. American and British expeditionary forces of the North Russia Campaign were armed with these rifles and sent to Murmansk and Arkhangelsk in the late summer of 1918 to prevent the large quantities of munitions delivered for Czarist forces from being captured by the Central Powers. Remaining rifles were used for the training of U.S. Army troops. Some were used to equip U.S. National Guard, SATC, and ROTC units. Designated "U.S. Rifle, 7.62mm, Model of 1916", these are among the rarest of American service arms. In 1917, 50,000 rifles were sent via Vladivostok to the Czechoslovak Legions in Siberia to aid in their attempt to secure passage to France.
Many of the New England Westinghouse and Remington Mosin-Nagants were sold to private citizens in the United States before World War II through the office of the Director of Civilian Marksmanship, the predecessor to the federal government's current Civilian Marksmanship Program.
Large numbers of Mosin-Nagants were captured by German and Austro-Hungarian forces and saw service with the rear-echelon forces of both armies, and also with the Imperial German Navy. Many of these weapons were sold to Finland in the 1920s.
Civil War, modernization, and wars with Finland
During the Russian Civil War, infantry and dragoon versions were still in production, though in dramatically reduced numbers. The rifle was widely used by all belligerents in the civil war. In 1924, following the victory of the Red Army, a committee was established to modernize the rifle, which had by then been in service for over three decades. This effort led to the development of the Model 91/30 rifle, which was based on the design of the original dragoon version. The barrel length was shortened by 7 cm (2.8 in). The sight measurements were converted from arshins to meters; and the front sight blade was replaced by a hooded post front sight less susceptible to being knocked out of alignment. There were also minor modifications to the bolt, but not enough to prevent interchangeability with the earlier Model 1891 and the so-called "Cossack dragoon" rifles.
Finland was a Grand Duchy in the Russian Empire until 1917, so Finns had long used the Mosin-Nagant in service with the Tsarist military. The rifle was used in the short civil war there and adopted as the service rifle of the new republic's army. Finland produced several variants of the Mosin-Nagant, all of them manufactured using the receivers of Russian-made, American-made, French-made or (later) Soviet-made rifles. Finland also utilized a number of captured M91 and M91/30 rifles with minimal modifications. As a result, the rifle was used on both sides of the Winter War and the Continuation War during World War II. Finnish Mosin-Nagants were produced by SAKO, Tikkakoski, and VKT, with some using barrels imported from Switzerland and Germany. In assembling M39 rifles, Finnish armorers re-used hexagonal receivers that dated back as far as 1891. Finnish rifles are characterized by Russian, French or American-made receivers stamped with a boxed SA, as well as many other parts produced in those countries and barrels produced in Finland, Switzerland, Austria, Belgium and Germany. The Finns also manufactured two-piece "finger splice" stocks for their Mosin-Nagant rifles.
In addition, the rifle was distributed as aid to Republican anti-Franco forces in the Spanish Civil War. Spanish Civil War Mosins can be readily identified by the wire sling hangers inserted in the slots in the forearm and buttstock meant to take the Russian "dog collars" for Russian-style slings, so the rifles could accept Western European-style rifle slings.
World War II
At the beginning of the war, the Mosin-Nagant 91/30 was the standard issue weapon of Soviet troops and millions of the rifles were produced and used in World War II by the largest mobilized army in history.
The Mosin-Nagant Model 1891/30 was modified and adapted as a sniper rifle from 1932 onwards with mounts and scopes from Germany at first and subsequently with domestic designs (PE, PEM) and from 1942 was issued with 3.5-power PU fixed focus scopes to Soviet snipers. It served quite prominently in the brutal urban battles on the Eastern Front, such as the Battle of Stalingrad, which made heroes of snipers like Vasily Zaitsev, Lyudmila Pavlichenko, Ivan Sidorenko, and Roza Shanina. Finland also employed the Mosin-Nagant as a sniper rifle, with similar success with their own designs and captured Soviet rifles. For example, Simo Häyhä is credited with having killed 505 Soviet soldiers, many of whom fell victim to his Finnish M/28-30 Mosin-Nagant rifle. Häyhä did not use a scope on his Mosin. In interviews Häyhä gave before his death, he said that the scope and mount designed by the Soviets required the shooter to expose himself too much and raise his head too high, increasing the chances of being spotted by the enemy.
In 1935-1936, the 91/30 was again modified, this time to lower production time. The hex receiver (actually octagonal) was changed to a round receiver. When war with Germany broke out, the need to produce Mosin-Nagants in vast quantities led to a further simplification of machining and a falling-off in finish of the rifles. The wartime Mosins are easily identified by the presence of tool marks and rough finishing that never would have passed the inspectors in peacetime. However, despite a lack of both aesthetic focus and uniformity, the basic functionality of the Mosins was unimpaired.
In addition, in 1938, a carbine version of the Mosin-Nagant, the M38, was issued. The carbine used the same cartridge and action as other Mosins, but the barrel was shortened by 21.6 cm (8.5 in) to bring the weapon down to an overall length of 101.6 cm (40.0 in), with the forearm shortened in proportion. The idea was to issue the M38 to troops such as combat engineers, signal corps, and artillerymen, who could conceivably need to defend themselves from sudden enemy advances, but whose primary duties lay behind the front lines. Significantly, the front sight of the M38 was positioned in such a way that the Model 91/30's cruciform bayonet could not be mounted to the muzzle even if a soldier obtained one.
An increase in urban combat led directly to the development of the Model M44 Mosin. In essence, the M44 is an M38 with a slightly modified forearm and with a permanently mounted cruciform bayonet that folds to the right when it is not needed. In terms of handiness, the M44 was an improvement on the Model 91/30, particularly for urban warfare; but few M44s saw combat on the Eastern Front.
By the end of the war, approximately 19.8 million rifles had been produced.
Increased world-wide use
In the years after World War II, the Soviet Union ceased production of all Mosin-Nagants and withdrew them from service in favor of the SKS series carbines and eventually the AK series rifles. Despite its increasing obsolescence, the Mosin-Nagant saw continued service throughout the Eastern bloc and the rest of the world for many decades to come. Mosin-Nagant rifles and carbines saw service on many fronts of the Cold War, from Korea and Vietnam to Afghanistan and along the Iron Curtain in Europe. They were kept not only as reserve stockpiles, but front-line infantry weapons as well. Finland was still producing the M39 Mosin-Nagant in small numbers as late as 1973
Virtually every country that received military aid from the Soviet Union, China, and Eastern Europe during the Cold War used Mosin-Nagants at various times. Middle Eastern countries within the sphere of Soviet influence--Egypt, Syria, Iraq, Afghanistan and Palestinian fighters--have received them in addition to other more modern arms. Mosin-Nagants have also seen action in the hands of both Soviet and Mujahadeen forces in Afghanistan during the Soviet Union's occupation of the country during the 1970s and the 1980s. Their use in Afghanistan continued on well into the 1990s and the early 21st century by Northern Alliance forces. Even after the collapse of the Soviet Union, Mosin-Nagants are still commonly found on modern battlefields around the world.
Mosin-Nagant Model 1891 Infantry Rifle
Model 1891 Infantry Rifle (Russian: ? 1891- ?): The primary weapon of Russian and Red Army infantry from 1891 to 1930. Between 1891 and 1910 the following modifications were made to the design of the rifle:
Inclusion of a reinforcing bolt through the finger groove (due to the adoption of a 147-grain pointed 'spitzer' round).
Elimination of the steel finger rest behind the trigger guard.
New barrel bands.
Installation of slot-type sling mounts to replace the more traditional swivels.
Mosin-Nagant Model 1891 Dragoon Rifle. (Note that the bolt is in the unlocked position)
Dragoon Rifle (Russian: ?): Intended for use by Dragoons: 64 mm (2.5 in) shorter and 0.4 kg (0.9 lb) lighter than the M1891. The Dragoon rifle's dimensions are identical to the later M1891/30 rifle, and most Dragoon rifles were eventually reworked into M1891/30s. Most such rifles, known to collectors as "ex-Dragoons", can be identified by their pre-1930 date stampings, but small numbers of Dragoon rifles were produced from 1930 to 1932 and after reworking became impossible to distinguish from purpose-built M1891/30s.
Cossack Rifle (?): Introduced for Cossack horsemen, it is almost identical to the Dragoon rifle but is sighted for use without a bayonet. These rifles were also issued without a bayonet.
Model 1907 Carbine: At 289 mm (11.4 in) shorter and 0.95 kg (2.1 lb) lighter than the M1891, this model was excellent for cavalry, engineers, signalers, and artillerymen. It was stocked nearly to the front sight and therefore did not take a bayonet. It was produced until at least 1917 in small numbers.
Mosin-Nagant Model 1891/30
Mosin-Nagant Model 1891/30 (1933)
Model 1891/30 ( ? 1891/30- ?, ): The most prolific version of the Mosin-Nagant. It was produced for standard issue to all Soviet infantry from 1930 to 1945. Most Dragoon rifles were also converted to the M1891/30 standard. It was commonly used as a sniper rifle in World War II. Early sniper versions had a 4× PE or PEM scope, a Soviet-made copy of a Zeiss design, while later rifles used smaller, simpler, and easier-to-produce 3.5× PU scopes. Because the scope was mounted above the chamber, the bolt handle was replaced with a longer handled, bent version on sniper rifles (known to Mosin collectors and shooters as a "bent bolt") so the shooter could work the bolt without the scope interfering with it. Like the US M1903A4 Springfield sniper rifle, the location of the scope above the receiver prevents the use of stripper clips. Its design was based on the Dragoon rifle with the following modifications:
Flat rear sights and restamping of sights in metres, instead of arshinii.
A cylindrical receiver, replacing the octagonal (commonly called "hex") receiver. Early production 91/30s (from 1930 to 1936) and converted Dragoon rifles retained the octagonal receiver. These rifles are less common and regarded as generally more desirable by collectors.
A hooded post front sight, replacing the blade on previous weapons.
Mosin-Nagant Model 1938 Carbine
Model 1938 Carbine: A carbine based on the M1891/30 design that was produced from 1939 to 1945 at the Izhevsk arsenal and in 1940 and 1944 at Tula. They were intended for use by second-echelon and noncombatant troops. Very few M38 carbines were made in 1945 and are highly sought after by collectors. Essentially a M1891/30 with a shortened barrel and shortened stock (the M38 is 1000 millimeters (40 in) in overall length versus 1230 millimeters (48 in) overall length for the Model 91/30), this carbine did not accept a bayonet and was in fact designed so that the standard Model 91/30 bayonet would not fit it. However many M38 carbines were fitted into M44 stocks by the Soviets as a wartime expedient. M38s in the correct M38 stock command a premium over M38s in M44 pattern stocks. The M38 was replaced by the M44 carbine in 1944.
Model 1944 Carbine: This carbine was introduced into service in late 1944 (with 50,000 service-test examples produced in 1943) and remained in production until 1948. They were produced from 1943 to 1948 at the Izhevsk arsenal and only 1944 at Tula. Its specifications are very similar to the M1938, with the unique addition of a permanently affixed, side-folding cruciform-spike bayonet. A groove for the folded bayonet is inlet into the right side of the stock. These were in use not only by the Soviet Union, but also its various satellite nations. Many of these were counterbored post-war.
Model 1891/59 Carbine: Commonly called "91/59s," the M1891/59s were created by shortening M1891/30 rifles to carbine length, with rear sight numbers partially ground off to reflect reduced range. These rifles are almost clones of the M38 except for the ground off M91/30 rear sight. The "1891/59" marking on the receiver suggests the carbines were created in or after 1959. It was initially thought that Bulgaria or another Soviet satellite country performed the conversions in preparation for a Western invasion that never came. Recent evidence suggests that the M91/59 was indeed produced in Bulgaria from Soviet-supplied wartime production M91/30s. Total production of the 91/59 is uncertain; figures as low as one million and as high as three million have appeared in firearm literature.
OTs-48/OTs-48K: The OTs-48/OTs-48K (-48?) sniper rifle was designed around 2000 in an attempt to make use of many surplus Mosin M1891/30 rifles which were still held in storage in Russia. Developed and manufactured "on order" by Central Design Bureau for Sporting and Hunting Arms (TSKIB SOO) in the city of Tula, this rifle is still in limited use by some Russian law enforcement agencies today.
After the Estonian War of Independence, Estonia had around 120,000 M/1891s in stock, later the Kaitseliit, the Estonian national guard, received some Finnish M28/30 rifles, a few modernised variants were also made by the Estonian Armory;
M1933 or 1891/33 was standard rifle of Estonian armed forces.
M1938: a further variant of M1933, 12,000 rifles.
KL300: a variant for Kaitseliit, 4,025 were made.
M1935"Lühendatud sõjapüss M1935": "shortened rifle M1935" was a shortened variant of M1933 with 600mm barrel, 6,770 rifles.
Finnish Army Mosin-Nagant Model 91.
Civil Guard Mosin-Nagant Model 24.
Finnish Army Mosin-Nagant Model 27.
Finnish Army Mosin-Nagant Model 27rv.
Civil Guard Mosin-Nagant Model 28.
Civil Guard Mosin-Nagant Model 28-30.
Civil Guard M/39 bayonet
M/28-76 marksman/sniper rifle
7.62 Tkiv 85 marksman/sniper rifle
Most Finnish Rifles were assembled by SAKO, Tikkakoski Oy, or VKT (Valtion Kivääritehdas, States Rifle factory, after wars part of Valtion Metallitehtaat (Valmet), State Metalworks). The Finnish cartridge 7.62×53mmR is a slightly modified variation of the Russian 7.62×54mmR, and is considered interchangeable with 54R. However, the older version of the Finnish military cartridge was loaded with the S-type bullet that had nominal diameter of .308. In 1936 the Finnish Army fielded a new standard service cartridge intended for both machine guns and rifles. This new cartridge was loaded with a new bullet designed in 1934 - the D-166, which had a nominal diameter of .310. The new service rifle m/39 was designed from the start around the D-166 thus it had nominal barrel diameter of .310.
Handloaded cartridges for Finnish rifles should however use a 0.308 inches (7.8 mm) bullet for use with other Finnish Mosin-Nagant variants instead of the 0.310 inches (7.9 mm) one which gives best results in M39, Soviet and most of other Mosin-Nagant rifles.
M/91: When Finland achieved independence from Russia, over 190,000 Model 1891 infantry rifles were already stockpiled in the ex-Russian military depots within Finland. As a result, the rifle was adopted as the standard Finnish Army weapon, and surplus Mosin-Nagants were purchased from other European nations which had captured them during World War I. These rifles were overhauled to meet Finnish Army standards and designated M/91. In the mid-1920s Tikkakoski made new barrels for m/91s. Later starting in 1940, Tikkakoski and VKT began production of new M/91 rifles. VKT production ceased in 1942 in favor of the newer M/39 rifle, but Tikkakoski production continued through 1944. The M/91 was the most widely issued Finnish rifle in both the Winter War and the Continuation War.
M/91rv: A cavalry rifle built from former Russian Model 1891 Dragoon rifles, modified with a sling slot based on the German Karabiner 98a. The original Russian sling slots were also retained.
M/24: The "Lotta Rifle," the Model 24 or Model 1891/24 was the first large-scale Mosin-Nagant upgrade project undertaken by the Finnish Suojeluskunta (Civil Guard), and there were, in fact three separate variations of the rifle. Barrels were produced by SIG (Schweizerische Industrie Gesellschaft) and by a German consortium. Swiss-produced barrels could be found in both standard Mosin-Nagant 1891 contour and in a heavier contour designed for improved accuracy, while all German-produced barrels were heavy weight barrels. The initial contract for the SIG-produced barrels was let on April 10, 1923, and was for 3,000 new barrels produced with the original Model 1891 barrel contour. A subsequent contract for 5,000 additional heavier barrels, stepped at the muzzle end to accept the standard Mosin-Nagant bayonet, was let the next year. The German contracts, starting in 1924 and running to 1926, were all for the heavier, stepped barrels with two contracts: one for 5,000 barrels and a second for 8,000 barrels. The German-made barrels are marked "Bohler-Stahl" on the under side of the chamber. All Model 24s are marked with the Civil Guard logo of three fir tree sprigs over a capital "S." All Model 24s are equipped with a coil spring around the trigger pin to improve the trigger pull and thus the accuracy of the rifle. The Model 24 was called the Lotta's Rifle ("Lottakivääri") after the women's auxiliary of the Civil Guard, known as the Lotta Svärd which was instrumental in raising funds to purchase and repair or refurbish some 10,000 rifles.
M/27: The Model 27 was the Finnish Army's first almost complete reworking of the Model 1891, it was nicknamed Pystykorva (literally "spitz") due to the front sight protector resembling the ears of a spitz. The receiver and magazine of the 1891 were retained, but a new shorter-length heavy-weight barrel was fitted. The sights were modified. The receivers and bolts were modified with "wings" being fitted to the bolt connecting bars that fit into slots machined into the receivers. The stocks were initially produced by cutting down 1891 stocks and opening up the barrel channels to accommodate the heavier barrel. New barrel bands and nose caps were fitted and a new bayonet was issued. The modified stocks proved to be weak, breaking when soldiers practiced bayonet fighting or firing with the bayonet fitted. These and other problems resulted in a slow-down of production in the mid-1930s while solutions to problems were engineered and existing stocks of rifles were modified. Produced from mid-1927 to 1940, the Model 27 was the Finnish Army's main battle rifle in the Winter War.
M/27rv: A cavalry carbine version of the M27, rv is short for ratsuväki (literally mounted force). 2217 were made, and were assigned to the most elite Finnish cavalry units. As a result of their heavy use, nearly half were lost over the course of the Winter and Continuation Wars. Most of the surviving examples were deemed beyond repair and scrapped, with slightly over 300 still existing. This makes it the rarest of all Finnish Mosin-Nagant models.
M/28: A variant designed by the White Guard. The M/28 differs from the Army's M/27 primarily in the barrel band design, which is a single piece compared to the M/27's hinged band, and an improved trigger design. Barrels for the M/28 were initially purchased from SIG, and later from Tikkakoski and SAKO.
M/28-30: An upgraded version of the M/28. The most noticeable modification is the new rear sight design. The same sight was used in following M39 rifle only exception being "1.5" marking for closest range to clarify it for users. According to micrometer measurements and comparison to modern Lapua D46/47 bullet radar trajectory data, markings are matched to Finnish Lapua D46/D46 bullet surprisingly accurately through whole adjustment range between 150 m and 2000 m.
The trigger was also improved by adding coil spring to minimize very long pre-travel. Following M39 does not have this improvement. The magazine was also modified to prevent jamming. Magazines were stamped with "HV" (Häiriö Vapaa = Jam Free) letters in right side of rifle. Later M39 uses identical design, but without "HV" -stamp. M/28-30 also have metal sleeve in fore-end of handguard, to reduce barrel harmonics change and to make barrel-stock contact more constant between shots and/or during environmental changes such as moisture and temperature. Later M39 does not have this upgrade.
M/28-30 model, serial number 60974, was also used by Simo Häyhä, a well-known Finnish sniper. M28/30 was used as Civil Guards competition rifle before World War II, as was the case with Simo Häyhä's personal rifle. Therefore, rifles were built very well, with highest grade barrels available and carefully matched headspace. Häyhä's rifle was still at PKarPr (Northern Karelia Brigade) museum in 2002, then moved to an unknown place by the Finnish Army.
M/91-35: A model proposed by the Finnish Army to replace both its M/27 and the White Guard's M/28 and M/28-30 rifles. The White Guard strongly objected to this plan, considering the M91/35 to have poor accuracy and excessive muzzle flash. It was never adopted, instead being supplanted by the M/39.
M/39: nicknamed "Ukko-Pekka" after the former President Pehr Evind Svinhufvud, a compromise between the Army and White Guard, adopted so as to standardize Mosin-Nagant production. The M/39 was derived largely from the M28-30, but included some alterations proposed by the Army. The M/39 also incorporated a semi-pistol grip into the stock, though some early examples used typical Mosin-Nagant straight stocks. Only 10 rifles were completed by the end of the Winter War, but 96,800 were produced after the Winter War and used in the Continuation War. Small numbers were assembled from leftover parts in the late 1960s through 1973, bringing the total production to approximately 102,000.
M/30: Tikkakoski produced improved, high-quality Model 1891/30 rifles in 1943 and 1944, designated M/30, using new barrels and parts from some of the almost 125,000 1891/30s captured in the Winter and Continuation Wars as well as 57,000 rifles bought from the Germans in 1944 (most of which were only suitable for use as parts donors). They were produced with both one- and two-piece stocks and either Soviet globe or Finnish blade foresights.
M/28-76: A special marksman and target rifle for continuation training and competition, produced in two different versions by the Finnish Army. They were built from modified M/28-30 and M/39 rifles.
7.62 Tkiv 85: A modern designated marksman/sniper rifle in which the original Mosin-Nagant receiver is modified and assembled by Valmet and Finnish Defence Forces (FDF) Asevarikko 1 (Arsenal 1) in Kuopio.
VZ91/38 Carbine: Very similar to the M91/59, it is an M38-style carbine produced by cutting down Model 1891 Infantry, Dragoon, and Cossack rifles. Few of these carbines exist, and the reason for their creation remains unclear. Like the M44, they have a bayonet groove cut into the right side of the stock, despite there being no evidence that the VZ91/38 design ever included a bayonet. The front sight features a wide base similar to post World War II M44's.
VZ54 Sniper Rifle: Based on the M1891/30, although it has the appearance of a modern sporting firearm. The VZ54 utilizes a Czech-made 2.5× magnification scope, as well as a unique rear sight. It also borrows some features from the Mauser design, such as locking screws and a K98k-style front sight hood.
VZ54/91 Sniper Rifle: Updated version of the VZ54 Sniper Rifle. The VZ54/91 utilizes an adjustable biathlon style stock with fully adjustable comb and butt plate. A rail beneath the forearm accepts adjustable sling swivels as well as a bipod. A Soviet manufactured PSO-1 scope also used on the SVD Dragunov sniper rifle is mounted on a side plate. It retains the front and rear sights of the VZ54.
A Chinese Type 53 carbine captured by US forces in Korea.
Type 53: A license-built version of the post-war Soviet M1944 carbine. As many of the carbines imported to the United States are constructed of both local Chinese parts and surplus Soviet parts, there is much debate as to when this mixture occurred. Type 53s are found both with and without the permanently attached folding bayonet, though the former is far more common. The Chinese Type 53 carbine saw extensive service with the People's Liberation Army from 1953 until the late 1950s/early 1960s when the PLA went over to the Chinese Type 56 carbine and the Chinese Type 56 assault rifle. Many Type 53 carbines were given to the People's Militia in China (The People's Militia used the Type 53 until 1982 when they were replaced with modern weapons. There is some evidence that the Type 53 carbine saw extensive use in the hands of the People's Militia during the years of the Great Leap Forward and the Cultural Revolution) and to North Vietnam (with many carbines ending up in the hands of the National Liberation Front in South Vietnam) and to the Khmer Rouge in Cambodia during the 1960s and 1970s. A significant number of Type 53 carbines were given to Albania and a few African countries as military aid by the Chinese during the 1960s. Some of these carbines appeared in the hands of the Kosovo Liberation Army during the late 1990s.
Mosin-Nagant Model 1948 Infantry Rifle Gyalogsági Puska, 48.M (48.Minta) Produced by the FEG (Fémáru Fegyver és Gépgyár) plant in Budapest, these high-quality versions of the Soviet Model 1891/30 were produced from 1949 to possibly as late as 1955. They are characterized by a high-quality finish and the marking of all parts with the "02" stamp.
Femaru-Fegyver es Gepgyar (FEG) manufactured a M1891 sniper version based on the 48 in the 1950s. This model was used extensively by the North Vietnamese Army (NVA) during the Vietnam War.
M/52: a direct copy of the original Soviet Model 1891/30 sniper rifle. Identifying features include:
Darkly blued steel and high quality machining.
An "02" stamp on every component of the rifle, identifying it as manufactured in Hungary
M44 Pattern: Domestically produced version of post war pattern Soviet M44 Carbine marked "02".
Triangular shaped markings, some with an arrow inside, on many components of the rifle. Normally three "R"'s surrounded by crossed stalks with leaves pointing outwards are on the top of the breech. Year stamps are quite visible. The trigger assembly is unique in the Romanian 91/30 and is adjustable. It is not interchangeable with other Mosins.
M44 Pattern: Domestically produced version of post war pattern Soviet M44 Carbine during the years 1953 to 1955. Variances to the Soviet pattern produced minor differences.
Suppressed M44 Pattern: Domestically produced adaptation of the M44, with a long integral suppressor and an LPS 4×6° TIP2 telescopic sight, same as the one used on the PSL rifle. Only a small number were modified, for use with the USLA - a very small counter-terrorism unit of the Securitate
M91/30 Pattern: Domestically produced version Soviet pattern M91 during the year 1955. Some of the guns are marked "INSTRUCTIE" and held in reserve for a secondary line of defense in case of invasion. The Instructie mark is typically, but not always, accompanied by a broad red band on the buttstock. Some collectors do not consider these safe to fire, but most appear to be in good working order although well worn and somewhat neglected. The "EXERCITIU" mark is found on rifles that seem to have been used specifically for training purposes only. The "EXERCITIU" rifles are easily recognized by the black paint on the entire butt of the stock. They are not intended to be fired since the firing pin is clipped and many times parts critical to their proper function are missing.
wz. 91/98/23: conversion to the 7.92mmx57 Mauser cartridge, with a magazine modified to feed rimless cartridges. Utilized original Russian spike bayonet.
wz. 91/98/25: conversion to the 7.92mmx57 Mauser cartridge, with a magazine modified to feed rimless cartridges and a bayonet mounting bar to allow the use of Mauser 1898 bayonets.
wz. 91/98/26: conversion to the 7.92mmx57 Mauser cartridge, with a magazine modified to feed rimless cartridges and a bayonet mounting bar to allow the use of Mauser 1898 bayonets. Modified two-piece ejector/interrupter similar to Mauser pattern rifles.
wz. 44: Domestically produced version of post war pattern Soviet M44 Carbine, Marked with the Polish "circle 11."
wz. 48: A Polish single shot military trainer modeled in the image of the Mosin Nagant M38 carbine. Produced from 1948 until 1960, the wz48 was used to train Czech and Polish military cadets. It is chambered in .22 long rifle.
Russian three-line rifle, caliber 7.62mm (.30 inches): Due to the desperate shortage of arms and the shortcomings of a still-developing domestic industry, the Russian government ordered 1.5 million M1891 infantry rifles from Remington Arms and another 1.8 million from New England Westinghouse in the United States. Some of these rifles were not delivered before the outbreak of the October Revolution and the subsequent signing of the Treaty of Brest-Litovsk which ended hostilities between the Central Powers and Russia. When the Bolsheviks took over the Russian government, they defaulted on the Imperial Russian contracts with the American arsenals, with the result that New England Westinghouse and Remington were stuck with hundreds of thousands of Mosin-Nagants. The US government bought up the remaining stocks, saving Remington and Westinghouse from bankruptcy. The rifles in Great Britain armed the US and British expeditionary forces sent to North Russia in 1918 and 1919. The rifles still in the US ended up being primarily used as training firearms for the US Army. Some were used to equip US National Guard, SATC and ROTC units. Collectors have taken to calling these rifles, "U.S. Magazine Rifle, 7.62mm, Model of 1916", though no official source for this designation has ever been cited. Ordnance documents refer to the rifles as "Russian three-line rifle, caliber 7.62mm (.30 inches)". In 1917, 50,000 of these rifles were sent via Vladivostok to equip the Czechoslovak Legions in Siberia to aid in their attempt to secure passage to France. During the interwar period, the rifles which had been taken over by the US military were sold to private citizens in the United States by the Director of Civilian Marksmanship, the predecessor agency to the current Civilian Marksmanship Program. They were sold for the sum of $3.00 each. If unaltered to chamber the US standard .30-06 Springfield rimless cartridge, these rifles are prized by collectors because they do not have the import marks required by law to be stamped or engraved on military surplus firearms brought into the United States from other countries.
Mosin-Nagants have been exported from Finland since the 1960s as its military modernized and decommissioned the rifles. Most of these have ended up as inexpensive surplus for Western nations.
In Russia the Mosin-Nagant action has been used to produce a limited number of commercial rifles, the most famous are the Vostok brand target rifles exported in Europe in the 1960s and 1970s chambered in the standard 7.62×54mmR round and in 6.5×54mmR, a necked-down version of the original cartridge designed for long range target shooting. Rifles in 6.5×54mmR use a necked-down 7.62×54mmR cartridge and were the standard rifle of the USSR's Olympic biathlon team until the International Olympic Committee revised the rules of the event to reduce the range to 50 meters and required all competitors to use rifles chambered in .22LR.
A number of the Model 1891s produced by New England Westinghouse and Remington were sold to private citizens in the United States by the U.S. government through the Director of Civilian Marksmanship Program between the two World Wars. Rifles from this program are valuable collectibles. Many of these American-made Mosin-Nagants were rechambered by wholesalers to the ubiquitous American .30-06 Springfield cartridge; some were done crudely, and others were professionally converted. Regardless of the conversion, a qualified gunsmith should examine the rifle before firing, and owners should use caution before firing commercial ammunition.
With the fall of the Iron Curtain, a large quantity of Mosin-Nagants have found their way onto markets outside of Russia as collectibles and hunting rifles. Due to the large surplus created by the Soviet small arms industry during World War II and the tendency of the former Soviet Union to retain and store large quantities of old but well-preserved surplus (long after other nations' militaries divested themselves of similar vintage materials), these rifles (mostly M1891/30 rifles and M1944 carbines) are inexpensive compared to other surplus arms of the same era.
There is serious collector interest in the Mosin-Nagant family of rifles, and they are popular with hobby shooters and hunters. The notched rear tangent iron sight is adjustable for elevation, and is calibrated in hundreds of meters (Arshins on earlier models). The front sight is a post that is not adjustable for elevation. Sight adjustment for windage was made by the armory before issue by drifting the sight left or right in its dovetail.
The limited sight adjustment leaves some hunters with the desire to add a scope, leading two companies to make adjustable sights for the Russian version of this rifle, Mojo and Smith-Sights. Several companies also make scope mounts for pistol scopes that can be mounted to the rear sight of the Model 91/30 without drilling or tapping.
They are capable of taking any game on the North American continent when correct ammunition is used. Sniper models, or 'former sniper' models without scope but with obviously covered scope mounting holes, can be obtained that display accuracy ranging from 2-4 inch (5-10 cm) 10-shot groups at 100 yards (90 m). The typical Finnish M39 model, which the Finns fitted with their own superior barrels, typically display accuracy averaging 2-3 inch (5-7.5 cm) 10-shot groups at 100 yards (90 m).
In addition, several American companies manufacture aftermarket rifle stocks that come inletted so a Mosin can be dropped directly into the stock without additional modification, for shooters who would prefer their ex-military rifles look more like civilian-made hunting rifles.
Along with aftermarket stocks, there have also been a growing number of aftermarket parts, and add-ons designed for the multiple variants of the Mosin Nagant battle rifle. Non-permanent optic mounts, such as the JMECK bracket or the Mankave rear sight adaptor have made it possible to mount a traditional optic to the rifle without the need to drill, or tap receiver/barrel of the weapon.
Other, more contentious modifications are version specific muzzle brakes, which are designed to prevent the barrel from rising (and consequently ruining the sight picture of the shooter), as well as lessening the recoil felt while shooting.
Other companies are experimenting with detachable, and semi-permanent magazine extensions which would increase the magazine capability from five rounds to ten rounds.
^ ? ? " ? ? ? ?" No 1430 25.11.2003 (Order of the Ministry of Internal Affairs of Ukraine "On the organization of civil service activities of the State Protection Service at the Ministry of Internal Affairs of Ukraine" No. 1430 of 25 November 2003.)