|Preferred IUPAC name
Methyl ethylene oxide
3D model (JSmol)
CompTox Dashboard (EPA)
|Melting point||-111.9 °C (-169.4 °F; 161.2 K)|
|Boiling point||35 °C (95 °F; 308 K)|
|41% (20 °C)|
|Vapor pressure||445 mmHg (20 °C)|
Refractive index (nD)
Heat capacity (C)
Std enthalpy of
|Main hazards||Extremely flammable|
|GHS Signal word||Danger|
|NFPA 704 (fire diamond)|
|Flash point||-37 °C (-35 °F; 236 K)|
|747 °C (1,377 °F; 1,020 K)|
|Lethal dose or concentration (LD, LC):|
LD50 (median dose)
|660 mg/kg (guinea pig, oral)|
380 mg/kg (rat, oral)
440 mg/kg (mouse, oral)
1140 mg/kg (rat, oral)
690 mg/kg (guinea pig, oral)
LC50 (median concentration)
|1740 ppm (mouse, 4 h)|
4000 ppm (rat, 4 h)
LCLo (lowest published)
|2005 ppm (dog, 4 h)|
4000 ppm (guinea pig, 4 h)
|NIOSH (US health exposure limits):|
|TWA 100 ppm (240 mg/m3)|
IDLH (Immediate danger)
|Ca [400 ppm]|
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
|what is ?)(|
Propylene oxide is an organic compound with the molecular formula CH3CHCH2O. This colourless volatile liquid with an odour resembling ether, is produced on a large scale industrially. Its major application is its use for the production of polyether polyols for use in making polyurethane plastics. It is a chiral epoxide, although it is commonly used as a racemic mixture.
Industrial production of propylene oxide starts from propylene. Two general approaches are employed, one involving hydrochlorination and the other involving oxidation. In 2005, about half of the world production was through chlorohydrin technology and one half via oxidation routes. The latter approach is growing in importance.
The mixture of 1-chloro-2-propanol and 2-chloro-1-propanol is then dehydrochlorinated. For example:
The other general route to propylene oxide involves oxidation of propylene with an organic peroxide. The reaction follows this stoichiometry:
In principle, this process produces only water was a side product. In practice, some ring-opened derivatives of PO are generated.
Like other epoxides, PO undergoes ring-opening reactions. With water, propylene glycol is produced. With alcohols, reactions, called hydroxylpropylation, analogous to ethoxylation occur. Grignard reagents add to propylene oxide to give secondary alcohols.
Some other reactions of propylene oxide include:
Between 60 and 70% of all propylene oxide is converted to polyether polyols by the process called alkoxylation. These polyols are building blocks in the production of polyurethane plastics. About 20% of propylene oxide is hydrolyzed into propylene glycol, via a process which is accelerated by acid or base catalysis. Other major products are polypropylene glycol, propylene glycol ethers, and propylene carbonate.
The United States Food and Drug Administration has approved the use of propylene oxide to pasteurize raw almonds beginning on September 1, 2007, in response to two incidents of contamination by Salmonella in commercial orchards, one incident occurring in Canada and one in the United States. Pistachio nuts can also be subjected to propylene oxide to control Salmonella.
Propylene oxide is commonly used in the preparation of biological samples for electron microscopy, to remove residual ethanol previously used for dehydration. In a typical procedure, the sample is first immersed in a mixture of equal volumes of ethanol and propylene oxide for 5 minutes, and then four times in pure oxide, 10 minutes each.
In 2016 it was reported that propylene oxide was detected in Sagittarius B2, a cloud of gas in the Milky Way weighing three million solar masses. It is the first chiral molecule to be detected in space.