|Name:||SR.N6 Winchester class|
|Builders:||British Hovercraft Corporation|
|Length:||17.78 m (58 ft 4 in)|
|Beam:||7.97 m (26 ft 2 in)|
|Height:||6.32 m (20 ft 9 in) on cushion|
|Propulsion:||1 Rolls-Royce Gnome turbine engines 1,050 hp (780 kW) for lift and propulsion driving single four-bladed variable-pitch propeller|
|Speed:||50 kn (93 km/h)|
|Range:||170 miles at 30 knots|
|Capacity:||58 seated passengers|
The Saunders-Roe (later British Hovercraft Corporation) SR.N6 hovercraft (also known as the Winchester class) was essentially a larger version of the earlier SR.N5 series. It incorporated several features that resulted in the type becoming one of most produced and commercially successful hovercraft designs in the world.
While the SR.N2 and SR.N5s operated in commercial service as trials craft, the SR.N6 has the distinction of being the first production hovercraft to enter commercial service. In comparison to the SR.N5, the SR.N6 was stretched in length, providing more than double the seating capacity. Some models of the craft were stretched further, enabling an even greater capacity.
Experience gained in the development of the SR.N6 has been attributed as heavily contributing towards the design and production of the largest civil hovercraft to be ever produced, the SR.N4. Several major design features of the SR.N6 appeared on both the SR.N4 and further hovercraft designs by Saunders-Roe and its successor, the British Hovercraft Corporation.
During the late 1950s and early 1960s, British inventor Sir Christopher Cockerell had, in cooperation with British aerospace manufacturer Saunders-Roe, developed a pioneering new form of transportation, embodied the form of the experimental SR.N1 vehicle, which became widely known as the hovercraft. By late 1964, Saunders-Roe had commenced design work on multiple hovercraft designs; in addition to the relatively huge SR.N4 and studies into a prospective 2,000 ton freighter, there was also interest in developing its existing smaller hovercraft range.
In particular, the company had observed there tp be customer demand for a model of the SR.N5 that would be capable of carrying a much greater payload; there was a view that the existing craft was uneconomic for what payload it could carry and that an expanded, or 'stretched', model would be able to rectify this. According to Saunders-Roe's own projections, an increase of the craft's payload by 110 per cent would only reduce performance by 10 per cent as the increased payload was in part offset by the expanded cushion area, which meant that cushion pressure would not need to be substantially increased instead.
The first craft to be lengthened in this manner, in effect becoming the first SR.N6, was the ninth SR.N5 to have been produced. Following three months of work to adapt the craft to the new configuration, this first prototype was launched for the first time on 9 March 1965. Portions of the SR.N6's development were performed in conjunction with Hovertravel, a newly-formed operating company located near Saunders-Roe's East Cowes facility. In June 1965, following an initial series of trials, the SR.N6 prototype was delivered to operated by Scandinavian Hovercraft Promotions of Oslo, Norway under the name 'Scanhover'; it was followed by a second craft later that same month.
The SR.N6 had been designed in such a fashion that it could be extended from its initial 36 seat capacity to 58 without having to perform a major redesign or incurring high building costs. Work on the stretched SR.N6 was headed by Ray Wheeler, the Chief Designer of the British Hovercraft Corporation (BHC) - which Saunders-Roe had by then merged into. Many components and systems remained unchanged, including the relatively expensive Bristol Gnome turboshaft engine. Perhaps the most substantial change on the stretched craft, beyond the increased length, was the adoption of a twin-propeller configuration, which was done in order to reduce tip speed and thus noise. Hovertravel produced their first stretched SR.N6, achieved with engineering support from the BHC, by converting an existing damaged SR.N6 and two SR.N5s.
The Saunders-Roe SR.N6 (also known as the Winchester class) is a medium-sized hovercraft primarily designed for passenger service. The initial models of the type were capable of accommodating up to 38 passengers, which was greater than the maximum capacity of 18 that could be carried by the smaller SR.N5. The SR.N6 was subsequently further stretched to accommodate a further 20 passengers; this capacity upgrade let to it being considered to be more viable for commercial operations than any previous hovercraft design. By eventually increasing the capacity to 58 seats, the SR.N6 Mk.1S became the first hovercraft to be capable of transporting a typical coach load of people. In a military configuration, the SR.N6 is capable of carrying up to 55 fully equipped troops, or alternatively up to 6 tons of equipment.
The SR.N6 was powered by a single marinised model of the Bristol Gnome turboshaft engine; this drove both a single rear-facing 9 ft (2.74 m) diameter 4-bladed Dowty Rotol variable-pitch propeller along with a 7 ft (2.13 m) diameter centrifugal lift fan. The Gnome engine was an expensive component for operators, leading to some establishing their own internal overhaul facilities and making arrangements with other Gnome operators, including the Royal Navy, to reduce costs from relying on costly services from Rolls-Royce Limited. Around 20 per cent of the operating costs of the type have been attributed to maintenance of the 4 ft flexible skirt, which reportedly lasted for up to 500 hours, while similar cost levels have been reported for fuel.
Early on, the SR.N6 was outfitted with an improved skirt, featuring fingers and forward puff ports, which resulted in improved forward control and reduced skirt wear; fingers had not been present upon the initial version of the skirt used prior to 1966. The endurance of the fingers would be progressively improved over time, issues with salt spray negatively affecting both the engine and propeller were also encountered early on. An initial experience of some components having short overhaul lifespans or being unreliable was encountered during early days. During the early years of not only the SR.N6 but other hovercraft as well, the hovercraft skirt remained an unresolved area of difficulty during this era.
The SR.N6 was piloted from a forward-seated position at the front of the main passenger cabin. The pilot would exercise control over the direction of the craft via a series of control surfaces that was located immediately behind the variable pitch propeller. Early on, pilots were normally aviators which had been recruited from the Royal Air Force and Fleet Air Arm, however it has been claimed that experienced mariners would often be more skilled at operating the type, if not taking more time to adapt to its atypical form of propulsion, in part due to their familiarity at safely navigating within uncontrolled maritime environments. For navigation purposes, some SR.N6s were outfitted with onboard radar; multiple radar arrangements were used with the type, including pilots receiving radio guidance from on-shore radar operators in some circumstances.
Norwegian operator Scanhover served as the SR.N6's launch customer. In June 1965, the first SR.N6 entered commercial service, and was quickly joined by another craft. They operated on a 120-mile route, with six stopping points, in the Ålesund area. These craft were later operated between Aarhus and Kalundborg in Denmark and, during February and March 1966, also successfully underwent cold weather trials in Sweden, in the Gulf of Bothnia. The introduction of regular hovercraft services in the form of the SR.N6 attracted worldwide interest.
On 24 July 1965, British operator Hovertravel took delivery of their first SR.N6, placing it into service in the Solent area on a route between the Ryde Transport Interchange on the Isle of Wight and Southsea. This route was particularly well suited to hovercraft, as the tidal conditions of the surrounding coastline made berthing ships difficult, as well as a high volume of traffic; by 2012, Hovertravel had become the oldest hovercraft operator in the Western world, continuing to operate the same route.
In 1966, operator P & A Campbell, in conjunction with Townsend Ferries, purchased SR.N6-024 to conduct their Townsend Car Ferries service, initially performing cross-Channel services between Dover and Calais, however this service did not prove popular and was terminated after roughly two months. During 1966 and 1967, Campbell toured various holiday resorts across Great Britain, offering pleasure rides on the craft. SR.N6-024 was subsequently sold to Hovertravel, who soon deployed it on board the Cunard ocean liner RMS Sylvania in order to perform practical demonstrations in the Mediterranean to officials of various nations as well as some trips for passengers on board.
In 1967, Hoverwork, a subsidiary of Hovertravel, operated a pair of SR.N6s at Expo 67, a World's fair held in Montreal, Canada, to provide passenger services between the exhibition site and Montreal itself. In 1968, a single Hoverwork SR.N6 traversed a 2,400 route of inhospitable jungle terrain within central South America, between Manaus, Brazil and Port of Spain,Trinidad, for a National Geographic scientific expedition. Between Hoverwork and Hovertravel, a fleet of up to nine SR.N6s was employed on both scheduled and chartered operations around the world.
Prior to its introduction of the far-larger SR.N4, British Rail's hovercraft operating division, named Seaspeed, decided to adopt a pair of SR.N6s for route proving and information gathering purposes. In October 1966, Charles Brindle and several engineers surveyed several potential sites on both the British and French sides of the English Channel, using an SR.N6 to determine their suitability for the future SR.N4 service. In late 1971, the company stretched its SR.N6 to the larger Mk 1S standard, and fitted more powerful Gnome engines to account for the increased payload. However, in the long term, it was determined by Seaspeed that the SR.N6 could not be profitable on the Cowes-Southampton route to which it had tasked the type.
During the late 1960s, Hoverlloyd also launched a cross-Channel service using a pair of SR.N6s, running four return trips per day. Like Seaspeed, Hoverlloyd used its SR.N6 fleet to gain experience prior to its own acquisition of the larger SR.N4.
The British Royal Marines operated SR.N6 XV589 in The Falkland Islands in the late 60's early 70's to evaluate them for use in remote regions.
The original prototype SR.N6 Mk.1 (009) is currently on display at the Hovercraft Museum in Lee-on-the-Solent, Hampshire, England. With 22,000 hours of service over a 20-year period it is the world's most extensively operated hovercraft. The museum has several other SR.N6 on display or in various states of restoration. One is operational and occasionally used for demonstrations.
The SR.N6 has been the subject of two popular toy versions. A small metal replica was produced for over twenty years by Matchbox Toys, while a much larger die-cast version was produced in the 1970s by Dinky Toys. A 12.7 cm model was released by Matchbox in 1974 as part of their Super Kings range.