In architecture and structural engineering, a space frame or space structure (3D truss) is a rigid, lightweight, truss-like structure constructed from interlocking struts in a geometric pattern. Space frames can be used to span large areas with few interior supports. Like the truss, a space frame is strong because of the inherent rigidity of the triangle; flexing loads (bending moments) are transmitted as tension and compression loads along the length of each strut.
Alexander Graham Bell from 1898 to 1908 developed space frames based on tetrahedral geometry. Bell's interest was primarily in using them to make rigid frames for nautical and aeronautical engineering, with the tetrahedral truss being one of his inventions. Dr. Ing. Max Mengeringhausen developed the space grid system called MERO (acronym of MEngeringhausen ROhrbauweise) in 1943 in Germany, thus initiating the use of space trusses in architecture. The commonly used method, still in use has individual tubular members connected at node joints (ball shaped) and variations such as the space deck system, octet truss system and cubic system. Stéphane de Chateau in France invented the Tridirectional SDC system (1957), Unibat system (1959), Pyramitec (1960). A method of tree supports was developed to replace the individual columns.Buckminster Fuller patented the octet truss in 1961 while focusing on architectural structures.
Space frames are typically designed using a rigidity matrix. The special characteristic of the stiffness matrix in an architectural space frame is the independence of the angular factors. If the joints are sufficiently rigid, the angular deflections can be neglected, simplifying the calculations.
The simplest form of space frame is a horizontal slab of interlocking square pyramids and tetrahedra built from aluminium or tubular steel struts. In many ways this looks like the horizontal jib of a tower crane repeated many times to make it wider. A stronger form is composed of interlocking tetrahedra in which all the struts have unit length. More technically this is referred to as an isotropic vector matrix or in a single unit width an octet truss. More complex variations change the lengths of the struts to curve the overall structure or may incorporate other geometrical shapes.
Within the meaning of space frame, we can find three systems clearly different between them:
Classification by the arrangement of its elements
Other examples classifiable as space frames are these:
o Industrial Buildings , Factory o Sports Hall o Warehouses o Swimming Pools o Conference Hall & Exhibition Center o Stadiums with Long Span distance o Museum and Fair Houses o Shopping Centers and Malls o Airports and Canopy o Exhibition hall o Mosque o Atrium
Space frames are a common feature in modern building construction; they are often found in large roof spans in modernist commercial and industrial buildings.
Examples of buildings based on space frames include:
Large portable stages and lighting gantries are also frequently built from space frames and octet trusses.
Space frames are sometimes used in the chassis designs of automobiles and motorcycles. In both a space frame and a tube-frame chassis, the suspension, engine, and body panels are attached to a skeletal frame of tubes, and the body panels have little or no structural function. By contrast, in a unibody or monocoque design, the body serves as part of the structure.
Tube-frame chassis pre-date space frame chassis and are a development of the earlier ladder chassis. The advantage of using tubes rather than the previous open channel sections is that they resist torsional forces better. Some tube chassis were little more than a ladder chassis made with two large diameter tubes, or even a single tube as a backbone chassis. Although many tubular chassis developed additional tubes and were even described as "space frames", their design was rarely correctly stressed as a space frame and they behaved mechanically as a tube ladder chassis, with additional brackets to support the attached components, suspension, engine etc. The distinction of the true space frame is that all the forces in each strut are either tensile or compression, never bending. Although these additional tubes did carry some extra load, they were rarely diagonalised into a rigid space frame.
The first true space frame chassis were produced in the 1930s by designers such as Buckminster Fuller and William Bushnell Stout (the Dymaxion and the Stout Scarab) who understood the theory of the true space frame from either architecture or aircraft design.
The first racing car to attempt a space frame was the Cisitalia D46 of 1946. This used two small diameter tubes along each side, but they were spaced apart by vertical smaller tubes, and so were not diagonalised in any plane. A year later, Porsche designed their Type 360 for Cisitalia. As this included diagonal tubes, it can be considered the first true space frame.
The Maserati Tipo 61 of 1959 (Birdcage) is often thought of as the first but in 1949 Dr. Robert Eberan-Eberhorst designed the Jowett Jupiter exhibited at that year's London Motor Show; the Jowett went on to take a class win at the 1950 Le Mans 24hr. Later, TVR, the small British car manufacturers developed the concept and produced an alloy-bodied two seater on a multi tubular chassis, which appeared in 1949.
Colin Chapman of Lotus introduced his first 'production' car, the Mark VI, in 1952. This was influenced by the Jaguar C-Type chassis, another with four tubes of two different diameters, separated by narrower tubes. Chapman reduced the main tube diameter for the lighter Lotus, but did not reduce the minor tubes any further, possibly because he considered that this would appear flimsy to buyers. Although widely described as a space frame, Lotus did not build a true space frame chassis until the Mark VIII, with the influence of other designers, with experience from the aircraft industry.
A large number of kit cars, possibly the majority made in the UK, use space frame construction, because manufacture in small quantity requires only simple and inexpensive jigs, and it is relatively easy for an amateur designer to achieve good stiffness with a space frame. Generally the space frames are MIG welded, although the more expensive kits often use TIG welding, a slower and more highly skilled process. Many of these resemble the Lotus Mark VII in general outline and mechanical layout, however others are close replicas of the AC Cobra or Italian supercars, but some are original designs resembling no other vehicle. Often, considerable effort has been made by the designers to produce true space frames, with all points of significant load braced in 3 dimensions, resulting in strength and stiffness comparable to, or better than, typical production cars. Others are tube frames but not true space frames because they use relatively large diameter tubes, often curved, which are carrying bending loads, but due to the large diameter remain adequately rigid. However some inferior designs are not true space frames, because the tubes are carrying considerable bending loads. This will result in considerable flexing due to dynamic loads, and ultimately fatigue fracture, a failure mechanism which is rare in a correctly designed true space frame. The reduced stiffness will also impair the handling.
A drawback of the space frame chassis is that it encloses much of the working volume of the car and can make access for both the driver and to the engine difficult. Some space frames have been designed with removable sections, joined by bolted pin joints. Such a structure had already been used around the engine of the Lotus Mark III. Although somewhat inconvenient, an advantage of the space frame is that the same lack of bending forces in the tubes that allow it to be modelled as a pin-jointed structure also means that such a removable section need not reduce the strength of the assembled frame.
Italian motorbike manufacturer Ducati extensively uses tube frame chassis on its models.