Pressure Drag
Get Pressure Drag essential facts below. View Videos or join the Pressure Drag discussion. Add Pressure Drag to your topic list for future reference or share this resource on social media.
Pressure Drag
Drag curve for a lifting body in steady flight

Parasitic drag is drag that acts on any object when the object is moving through a fluid. Parasitic drag is a combination of form drag and skin friction drag.[1] It affects all objects regardless of whether they are capable of generating lift.

The other components of total drag on an aircraft, such as lift-induced drag and wave drag, are separate types of drag, and are not components of parasitic drag.

Form drag

Form drag or pressure drag arises because of the shape of the object. The general size and shape of the body are the most important factors in form drag; bodies with a larger presented cross-section will have a higher drag than thinner bodies; sleek ("streamlined") objects have lower form drag. Form drag follows the drag equation, meaning that it increases with velocity, and thus becomes more important for high-speed aircraft.

Form drag depends on the longitudinal section of the body. A prudent choice of body profile is essential for a low drag coefficient. Streamlines should be continuous, and separation of the boundary layer with its attendant vortices should be avoided.

Skin friction drag

Skin friction drag arises from the friction of the fluid against the "skin" of the object that is moving through it. Skin friction arises from the interaction between the fluid and the skin of the body, and is directly related to the wetted surface, the area of the surface of the body that is in contact with the fluid. Air in contact with a body will stick to the body's surface and that layer will tend to stick to the next layer of air and that in turn to further layers, hence the body is dragging some amount of air with it. The force required to drag an "attached" layer of air with the body is called skin friction drag. Skin friction drag imparts some momentum to a mass of air as it passes through it and that air applies a retarding force on the body. As with other components of parasitic drag, skin friction follows the drag equation and rises with the square of the velocity.

Skin friction is caused by viscous drag in the boundary layer around the object. The boundary layer at the front of the object is usually laminar and relatively thin, but becomes turbulent and thicker towards the rear. The position of the transition point from laminar to turbulent flow depends on the shape of the object. There are two ways to decrease friction drag: the first is to shape the moving body so that laminar flow is possible. The second method is to increase the length and decrease the cross-section of the moving object as much as practicable. To do so, a designer can consider the fineness ratio, which is the length of the aircraft divided by its diameter at the widest point (L/D). It is mostly kept 6:1 for subsonic flows. Increase in length increases Reynolds number. With Reynolds no. in the denominator for skin friction coefficient's relation, as its value is increased (in laminar range), total friction drag is reduced. While decrease in cross-sectional area decreases drag force on the body as the disturbance in air flow is less. For wings of an aircraft, a decrease in length (chord) of the wings will reduce "induced" drag though, if not the friction drag.

The skin friction coefficient, , is defined by

where is the local wall shear stress, and q is the free-stream dynamic pressure.[2] For boundary layers without a pressure gradient in the x direction, it is related to the momentum thickness as

For comparison, the turbulent empirical relation known as the One-seventh Power Law (derived by Theodore von Kármán) is:

where is the Reynolds number.[3]

For a laminar flow over a plate, the skin friction coefficient can be determined using the following formula:[4]

Profile drag

Profile drag is a term usually applied to the parasitic drag acting on a wing. With a two-dimensional wing there is no lift-induced drag so the whole of the drag is profile drag. With a three-dimensional wing the total drag minus the lift-induced drag is the profile drag[5] - it is defined as the sum of form drag and skin friction.[6]

See also


  1. ^ Clancy, L.J. (1975). Aerodynamics, Sub-section 5.9. Pitman Publishing. ISBN 0 273 01120 0
  2. ^ "Skin friction coefficient -- CFD-Wiki, the free CFD reference". Retrieved 2018.
  3. ^ Introduction to Flight, John Anderson Jr., 7th edition
  4. ^ tec-science (2020-05-31). "Drag coefficient (friction and pressure drag)". tec-science. Retrieved .
  5. ^ Anderson, John D. (1984). Fundamentals of Aerodynamics, p.192, 233. McGraw-Hill Book Company ISBN 0-07-001656-9
  6. ^ "Profile drag definition and meaning - Collins English Dictionary". Retrieved 2018.

  This article uses material from the Wikipedia page available here. It is released under the Creative Commons Attribution-Share-Alike License 3.0.



Music Scenes